This section provides a list of the most common commands and their output for the examples used in this guide. These examples are from the final topology with two VxRail clusters deployed, as shown in the SmartFabric topology with connections to VxRail nodes and external network figure.
General commands
show version
Leaf and spine switches must be running a supported version of SmartFabric OS10. Run the show version command to check the operating system version. SmartFabric OS10 is available on Dell Digital Locker (account required).
Leaf1A# show version
Dell EMC Networking OS10 Enterprise
Copyright (c) 1999-2022 by Dell Inc. All Rights Reserved.
OS Version: 10.5.4.4
Build Version: 10.5.4.4.1
Build Time: 2022-09-26T12:09:20+0000
System Type: S5248F-ON
Architecture: x86_64
Up Time: 1 day 03:13:45
show license status
Run the command show license status to verify license installation. The License Type: field should indicate PERPETUAL. If an evaluation license is installed, licenses purchased from Dell are available for download on Dell Digital Locker. Installation instructions are provided in the Dell SmartFabric OS10 User Guide on Dell Networking OS10 Info Hub.
Leaf1A# show license status
System Information
---------------------------------------------------------
Vendor Name : Dell EMC
Product Name : S5248F-ON
Hardware Version : A01
Platform Name : x86_64-dellemc_s5248f_c3538-r0
PPID : CN046MRJCES0089K0015
Service Tag : 690ZZP2
Product Base :
Product Serial Number:
Product Part Number :
License Details
----------------
Software : OS10-Enterprise
Version : 10.5.4.4
License Type : PERPETUAL
License Duration: Unlimited
License Status : Active
License location: /mnt/license/690ZZP2.lic
---------------------------------------------------------
show interface status
The show interface status | grep up command is used to verify required interfaces are up, and links are established at their appropriate speeds. In this example, ports 1/1/1-1/1/4 are VxRail nodes, port 1/1/9:1 is a jump host, ports 1/1/49-1/1/52 are the VLTi, ports 1/1/53-1/1/54 are uplinks to the external network, and ports 1/1/55-1/1/56 are uplinks to the spines.
Leaf1A# show interface status | grep up
Port Description Status Speed Duplex Mode Vlan Tagged-Vlans
Eth 1/1/1 up 25G full T -
Eth 1/1/2 up 25G full T -
Eth 1/1/3 up 25G full T -
Eth 1/1/4 up 25G full T -
Eth 1/1/9:1 up 10G full T -
Eth 1/1/49 up 100G full -
Eth 1/1/50 up 100G full -
Eth 1/1/51 up 100G full -
Eth 1/1/52 up 100G full -
Eth 1/1/53 up 100G full -
Eth 1/1/54 up 100G full -
Eth 1/1/55 up 100G full -
Eth 1/1/56 up 100G full -
show port-channel summary
The show port-channel summary command is used to view port channel numbers, interfaces used, and status. Port channel 1 (number may vary) is the L2 uplink to the external network, if used. Port channels 96 through 97 (numbers may vary) are automatically created spine uplinks. The VLTi is automatically configured as a static LAG using port channel 1000. Ports 1/1/53 and 1/1/54 are port channel members, and (P)
indicates each is up and active.
Leaf1A# show port-channel summary
Flags: D - Down I - member up but inactive P - member up and active
U - Up (port-channel) F - Fallback Activated
--------------------------------------------------------------------------------
Group Port-Channel Type Protocol Member Ports
--------------------------------------------------------------------------------
1 port-channel1 (U) Eth DYNAMIC 1/1/53(P) 1/1/54(P)
96 port-channel96 (U) Eth STATIC 1/1/55(P)
97 port-channel97 (U) Eth STATIC 1/1/56(P)
1000 port-channel1000 (U) Eth STATIC 1/1/49(P) 1/1/50(P) 1/1/51(P) 1/1/52(P)
show virtual network
The show virtual network command is used to view virtual networks, VLANs, and interfaces assigned to each VLAN. Port channel 1 (number may vary) is the L2 uplink to the external network if configured. Port channel 1000 is the VLTi. Interfaces 1/1/1-1/1/3 are connected to the VxRail nodes in the first cluster. Interface 1/1/4 is connected to the VxRail node in the second cluster. Interface 1/1/9:1, shown under VLAN 1811, is the jump host port.
Leaf1A# show virtual-network
Codes: DP - MAC-learn Dataplane, CP - MAC-learn Controlplane, UUD - Unknown-Unicast-Drop
Un-tagged VLAN: 4080
Virtual Network: 1811
VLTi-VLAN: 1811
Members:
Untagged: ethernet1/1/9:1
VLAN 1811: port-channel1, port-channel1000, ethernet1/1/1, ethernet1/1/2, ethernet1/1/3, ethernet1/1/4
VxLAN Virtual Network Identifier: 1811
Source Interface: loopback2(172.30.0.0)
Remote-VTEPs (flood-list): 172.30.0.3(CP)
Virtual Network: 1812
VLTi-VLAN: 1812
Members:
VLAN 1812: port-channel1000, ethernet1/1/1, ethernet1/1/2, ethernet1/1/3
VxLAN Virtual Network Identifier: 1812
Source Interface: loopback2(172.30.0.0)
Remote-VTEPs (flood-list): 172.30.0.3(CP)
Virtual Network: 1813
VLTi-VLAN: 1813
Members:
VLAN 1813: port-channel1000, ethernet1/1/1, ethernet1/1/2, ethernet1/1/3
VxLAN Virtual Network Identifier: 1813
Source Interface: loopback2(172.30.0.0)
Remote-VTEPs (flood-list): 172.30.0.3(CP)
Virtual Network: 1814
VLTi-VLAN: 1814
Members:
VLAN 1814: port-channel1000, ethernet1/1/1, ethernet1/1/2, ethernet1/1/3
VxLAN Virtual Network Identifier: 1814
Source Interface: loopback2(172.30.0.0)
Remote-VTEPs (flood-list): 172.30.0.3(CP)
Virtual Network: 1815
VLTi-VLAN: 1815
Members:
VLAN 1815: port-channel1000, ethernet1/1/1, ethernet1/1/2, ethernet1/1/3
VxLAN Virtual Network Identifier: 1815
Source Interface: loopback2(172.30.0.0)
Remote-VTEPs (flood-list): 172.30.0.3(CP)
Virtual Network: 1822
VLTi-VLAN: 1822
Members:
VLAN 1822: port-channel1000, ethernet1/1/4
VxLAN Virtual Network Identifier: 1822
Source Interface: loopback2(172.30.0.0)
Remote-VTEPs (flood-list): 172.30.0.3(CP)
Virtual Network: 1823
VLTi-VLAN: 1823
Members:
VLAN 1823: port-channel1000, ethernet1/1/4
VxLAN Virtual Network Identifier: 1823
Source Interface: loopback2(172.30.0.0)
Remote-VTEPs (flood-list): 172.30.0.3(CP)
Virtual Network: 1824
VLTi-VLAN: 1824
Members:
VLAN 1824: port-channel1000, ethernet1/1/4
VxLAN Virtual Network Identifier: 1824
Source Interface: loopback2(172.30.0.0)
Remote-VTEPs (flood-list): 172.30.0.3(CP)
Virtual Network: 1825
VLTi-VLAN: 1825
Members:
VLAN 1825: port-channel1000, ethernet1/1/4
VxLAN Virtual Network Identifier: 1825
Source Interface: loopback2(172.30.0.0)
Remote-VTEPs (flood-list): 172.30.0.3(CP)
Virtual Network: 3939
Description: In-band SmartFabric Services discovery network
VLTi-VLAN: 3939
Members:
VLAN 3939: port-channel1000, ethernet1/1/1, ethernet1/1/2, ethernet1/1/3, ethernet1/1/4
VxLAN Virtual Network Identifier: 3939
Source Interface: loopback2(172.30.0.0)
Remote-VTEPs (flood-list): 172.30.0.1(CP),172.30.0.2(CP),172.30.0.3(CP)
Virtual Network: 4091
Description: Default untagged network for client onboarding
VLTi-VLAN: 4091
Members:
Untagged: ethernet1/1/1, ethernet1/1/2, ethernet1/1/3, ethernet1/1/4
VLAN 4091: port-channel1000
VxLAN Virtual Network Identifier: 4091
Source Interface: loopback2(172.30.0.0)
Remote-VTEPs (flood-list): 172.30.0.1(CP),172.30.0.2(CP),172.30.0.3(CP)
show lldp neighbors
The show lldp neighbors command is useful for identifying connected equipment. Interfaces 1/1/1-4 are connected to the VxRail nodes, and Interface 1/1/9:1 is connected to the jump host. Interfaces 1/1/53-54 are connected to the external network, and 1/1/55-56 are connected to the spines. Mgmt1/1/1 is connected to the OOB management switch.
Leaf1A# show lldp neighbors
Loc PortID Rem Host Name Rem Port Id Rem Chassis Id
----------------------------------------------------------------------------------
ethernet1/1/1 Not Advertised 1c:34:da:55:f3:5c 1c:34:da:55:f3:5e
ethernet1/1/1 Not Advertised 1c:34:da:55:f3:5c 1c:34:da:55:f3:5c
ethernet1/1/1 c1-vxrail-03.dell... 1c:34:da:55:f3:5c vmnic0
ethernet1/1/2 Not Advertised 98:03:9b:0f:84:aa 98:03:9b:0f:84:ac
ethernet1/1/2 Not Advertised 98:03:9b:0f:84:aa 98:03:9b:0f:84:aa
ethernet1/1/2 c1-vxrail-02.dell... 98:03:9b:0f:84:aa vmnic0
ethernet1/1/3 Not Advertised 1c:34:da:55:f3:4c 1c:34:da:55:f3:4e
ethernet1/1/3 Not Advertised 1c:34:da:55:f3:4c 1c:34:da:55:f3:4c
ethernet1/1/3 c1-vxrail-01.dell... 1c:34:da:55:f3:4c vmnic0
ethernet1/1/4 Not Advertised 98:03:9b:0f:83:7a 98:03:9b:0f:83:7c
ethernet1/1/4 Not Advertised 98:03:9b:0f:83:7a 98:03:9b:0f:83:7a
ethernet1/1/4 c2-vxrail-04.dell... 98:03:9b:0f:83:7a vmnic0
ethernet1/1/9:1 Not Advertised 24:6e:96:3a:13:48 24:6e:96:3a:13:48
ethernet1/1/49 Leaf1B ethernet1/1/49 8c:04:ba:a7:f0:c0
ethernet1/1/50 Leaf1B ethernet1/1/50 8c:04:ba:a7:f0:c0
ethernet1/1/51 Leaf1B ethernet1/1/51 8c:04:ba:a7:f0:c0
ethernet1/1/52 Leaf1B ethernet1/1/52 8c:04:ba:a7:f0:c0
ethernet1/1/53 N9K-External-A Ethernet1/49 a0:b4:39:83:fa:58
ethernet1/1/54 N9K-External-B Ethernet1/49 a0:b4:39:83:fa:f8
ethernet1/1/55 Spine1 ethernet1/1/1 8c:04:ba:b7:9a:40
ethernet1/1/56 Spine2 ethernet1/1/1 8c:04:ba:b7:c5:c0
mgmt1/1/1 OOB-Mgmt-1 ethernet1/1/1 88:6f:d4:b0:78:e2
show ip interface brief
Run the show ip interface brief command to verify connected interfaces are up, and IP addresses are configured correctly.
In the output below, interfaces 1/1/1-1/1/4 are connected to the VxRail nodes, 1/1/49-1/1/52 are the VLTi, 1/1/53-1/1/54 are L3 uplinks to the external switches, and 1/1/55-1/1/56 are connections to the Spine switches. IP addresses assigned to VLANs 4000-4094 and Loopback interfaces are for SFS internal use. The remaining IP addresses shown are configured in the steps in this guide. VLAN 4090, Loopback 1, and Loopback 2 are automatically configured by SFS. VLAN 4090 is used for iBGP, Loopback 1 is the router ID, and Loopback 2 is the VTEP IP address.
Leaf1A# show ip interface brief
Ethernet 1/1/1 unassigned YES unset up up
Ethernet 1/1/2 unassigned YES unset up up
Ethernet 1/1/3 unassigned YES unset up up
Ethernet 1/1/4 unassigned YES unset up up
Ethernet 1/1/49 unassigned YES unset up up
Ethernet 1/1/50 unassigned YES unset up up
Ethernet 1/1/51 unassigned YES unset up up
Ethernet 1/1/52 unassigned YES unset up up
Ethernet 1/1/53 192.168.1.1/31 YES manual up up
Ethernet 1/1/54 192.168.2.1/31 YES manual up up
Ethernet 1/1/55 unassigned YES unset up up
Ethernet 1/1/56 unassigned YES unset up up
Management 1/1/1 100.67.76.12/24 YES manual up up
Vlan 4000 unassigned YES unset up up
Vlan 4001 172.16.0.4/31 YES manual up up
Vlan 4003 172.16.0.8/31 YES manual up up
Vlan 4089 unassigned YES unset up up
Vlan 4090 172.16.0.0/31 YES manual up up
Vlan 4094 unassigned YES unset up up
Port-channel 96 unassigned YES unset up up
Port-channel 97 unassigned YES unset up up
Port-channel 1000 unassigned YES unset up up
Loopback 1 172.16.128.0/32 YES manual up up
Loopback 2 172.30.0.0/32 YES manual up up
Virtual-network 1811 172.18.11.253/24 YES manual up up
Virtual-network 3939 unassigned YES unset up up
show ip bgp summary
Run the show ip bgp summary command to verify that BGP is up for each neighbor. When BGP is up, uptime is shown in the Up/Down column. The neighbors for Leaf1A shown in the output below are Leaf1B, External-A, and External-B.
Leaf1A# show ip bgp summary
BGP router identifier 172.16.128.0 local AS number 65011
Neighbor AS MsgRcvd MsgSent Up/Down State/Pfx
172.16.0.0 65011 13 16 00:46:59 8
172.16.0.5 65012 56 55 00:38:19 15
172.16.0.15 65012 50 51 00:37:57 15
192.168.1.0 65101 12 14 00:07:30 8
192.168.2.0 65101 8 9 00:04:14 8
show ip route
With L3 uplinks, the show ip route command is used to ensure the leaf switches have routes to the external network, 172.19.11.0/24 in this example, to reach the DNS server. This BGP-discovered route is shown in the output below.
Leaf1A# show ip route
Codes: C - connected
S - static
B - BGP, IN - internal BGP, EX - external BGP, EV - EVPN BGP
O - OSPF, IA - OSPF inter area, N1 - OSPF NSSA external type 1,
N2 - OSPF NSSA external type 2, E1 - OSPF external type 1,
E2 - OSPF external type 2, * - candidate default,
+ - summary route, > - non-active route
Gateway of last resort is not set
Destination Gateway Dist/Metric Change
-------------------------------------------------------------------------------------
B EX 10.0.2.1/32 via 192.168.1.0 20/0 23:23:21
B EX 10.0.2.2/32 via 192.168.2.0 20/0 23:22:36
C 172.16.0.0/31 via 172.16.0.0 vlan4090 0/0 21:01:01
B IN 172.16.0.2/31 via 172.16.0.1 200/0 20:58:03
C 172.16.0.4/31 via 172.16.0.4 vlan4001 0/0 21:08:33
B IN 172.16.0.6/31 via 172.16.0.1 200/0 20:01:51
C 172.16.0.8/31 via 172.16.0.8 vlan4003 0/0 20:01:54
B EX 172.16.0.10/31 via 172.16.0.5 20/0 21:05:24
B EX 172.16.0.12/31 via 172.16.0.9 20/0 19:57:31
B EX 172.16.0.14/31 via 172.16.0.5 20/0 20:01:20
via 172.16.0.9
B EX 172.16.0.16/31 via 172.16.0.5 20/0 21:05:24
B EX 172.16.0.18/31 via 172.16.0.9 20/0 19:57:31
C 172.16.128.0/32 via 172.16.128.0 loopback1 0/0 23:56:45
B IN 172.16.128.1/32 via 172.16.0.1 200/0 20:58:03
B EX 172.16.128.2/32 via 172.16.0.5 20/0 21:05:24
B EX 172.16.128.3/32 via 172.16.0.9 20/0 19:57:31
B EX 172.16.128.4/32 via 172.16.0.5 20/0 20:01:20
via 172.16.0.9
B EX 172.16.128.5/32 via 172.16.0.5 20/0 20:01:20
via 172.16.0.9
C 172.18.11.0/24 via 172.18.11.253 virtual-network1811 0/0 22:03:09
B EX 172.19.11.0/24 via 192.168.1.0 20/0 23:22:36
via 192.168.2.0
C 172.30.0.0/32 via 172.30.0.0 loopback2 0/0 23:56:48
B EX 172.30.0.1/32 via 172.16.0.5 20/0 21:05:24
B EX 172.30.0.2/32 via 172.16.0.9 20/0 19:57:31
B EX 172.30.0.3/32 via 172.16.0.5 20/0 20:01:20
via 172.16.0.9
C 192.168.1.0/31 via 192.168.1.1 ethernet1/1/53 0/0 23:23:39
B IN 192.168.1.2/31 via 172.16.0.1 200/0 20:58:03
C 192.168.2.0/31 via 192.168.2.1 ethernet1/1/54 0/0 23:22:54
B IN 192.168.2.2/31 via 172.16.0.1 200/0 20:58:03
VLT commands
show vlt domain_id
This command is used to validate the VLT configuration status. In SmartFabric mode, the VLT domain ID is 255. The Role for one switch in the VLT pair is primary, and its peer switch (not shown) is assigned the Secondary role. The VLTi Link Status and VLT Peer Status must both be up.
Leaf1A# show vlt 255
Domain ID : 255
Unit ID : 2
Role : primary
Version : 3.1
Local System MAC address : 3c:2c:30:89:1b:80
Role priority : 32768
VLT MAC address : 8c:04:ba:a7:f0:c0
IP address : fda5:74c8:b79e:1::2
Delay-Restore timer : 90 seconds
Peer-Routing : Disabled
Peer-Routing-Timeout timer : 0 seconds
Multicast peer-routing timer : 300 seconds
VLTi Link Status
port-channel1000 : up
VLT Peer Unit ID System MAC Address Status IP Address Version
----------------------------------------------------------------------------------
1 8c:04:ba:a7:f0:c0 up fda5:74c8:b79e:1::1 3.1
show vlt domain_id backup-link
This command is used to verify VLT peers are communicating on the backup link over the OOB management network. The Destination is the management IP address of the peer. The Peer Heartbeat status must be Up.
Leaf1A# show vlt 255 backup-link
VLT Backup Link
------------------------
Destination : 100.67.76.11
Peer Heartbeat status : Up
Heartbeat interval : 30
Heartbeat timeout : 90
Destination VRF : default
show vlt domain_id mismatch
This command highlights any potential configuration issues between VLT peers. All items must indicate No mismatch.
Leaf1A# show vlt 255 mismatch
VLT-MAC mismatch:
No mismatch
Peer-routing mismatch:
No mismatch
VLAN mismatch:
No mismatch
VLT VLAN mismatch:
No mismatch
VLT Virtual Network Mismatch:
Virtual Network Name Mismatch:
No mismatch
Virtual Network VLTi-VLAN Mismatch:
No mismatch
Virtual Network Mode Mismatch:
No mismatch
Virtual Network Tagged Interfaces Mismatch:
No mismatch
Virtual Network Untagged Interfaces Mismatch:
No mismatch
Virtual Network VNI Mismatch:
No mismatch
Virtual Network Remote-VTEP Mismatch:
No mismatch
Virtual Network anycast ip Mismatch:
No mismatch
Virtual Network anycast mac Mismatch:
No mismatch
EVPN Mismatch:
EVPN Mode Mismatch:
No mismatch
EVPN EVI Mismatch:
No mismatch
NVE Mismatch:
No mismatch
DHCP Snooping Mismatch:
Global Snooping Configuration Mismatch
------------------------------------------------------------
Codes: SE - Static Entry Mismatch
DT - DAI Trust Mismatch
ST - Snooping Trust Mismatch
SAV - Source-Address-Validation Mismatch
ARP - ARP Inspection Mismatch
VS - VLAN Snooping Mismatch
Interface Interface Snooping Configuration Mismatch
---------------------------------------------------------------------
Multicast routing mismatches:
Global status:
Parameter VRF Local Peer
---------------------------------------------------------------------
No mismatch
Vlan status IPv4 IPv6
VlanId Local Peer Local Peer
---------------------------------------------------------------------
No mismatch