- In the vSphere Client, launch the web console for the OMNI VM.
- Log in with the default OMNI VM username, admin, and password, admin. The first time you log in, follow the prompts to change the admin password.
- The OMNI Menudisplays.
- Select 0. Full setup. The Network Manager terminal user interface ( TUI) opens.Note: In the TUI, use the Tab and Arrow keys to navigate and the Enter key to select.
- Select Edit a connection > Wired connection 1.
- In the Edit Connectionwindow, make the following settings:
- Change the profile name to vCenter Server network. OMNI uses this connection to communicate with the vCenter Server on the External Management network, VLAN 1811 in this guide.Note: The Device field is automatically populated with a MAC address and (ens160).
- Set the IPv4 Configuration to Manual.
- Next to IPv4 Configuration, select Show to expand the additional fields.
- Enter the OMNI VM IP Address/prefix, Gateway, DNS server, and Search domain. The values used for this example are shown in the figure below.Note: The example shown in the figure below is with L2 uplinks, so the DNS server has an IP address on the same network as the OMNI VM, 172.18.11.50 in this example. If L3 uplinks are used, the DNS server will be on a different network. For the L3 uplink examples in this guide, the DNS server IP address is 172.19.11.50.
- Set the IPv6 Configuration to Ignore.
- Change the profile name to vCenter Server network. OMNI uses this connection to communicate with the vCenter Server on the External Management network, VLAN 1811 in this guide.
- Default values are used for the remaining settings. When complete, the Edit Connectionwindow appears as shown in the figure below.
- Select OK. The Ethernet connections list displays.
- Select Wired connection 2.
- In the Edit Connectionwindow, make the following settings:
- Change the profile name to SFS management network. OMNI uses this connection to communicate with SFS on VLAN 3939.Note: The Device field is automatically populated with a MAC address and (ens192).
- Set IPv4 Configuration to Disabled.
- Set IPv6 Configuration to Link-Local.
- Next to IPv6 Configuration, select Show to expand the IPv6 configuration fields.
- Next to Routing, select Edit > Add.
- Set the Destination/Prefix to fde1:53ba:e9a0:cccc::/64. Leave the remaining values at their default settings.
Note: Only part of the Destination/Prefix field is visible on the screen. Be sure it is set to fde1:53ba:e9a0:cccc::/64. - Change the profile name to SFS management network. OMNI uses this connection to communicate with SFS on VLAN 3939.
- Select OK > OK > Back to return to the Network Manager TUI menu.
- On the Network Manager TUI menu, select Activate a connection. The connection activation window displays.Note: When active, connection names have an asterisk (*) next to them. The activation steps only apply to the two Ethernet connections. Ignore the Veth connections.
- Deactivate both Ethernet connections as follows:
- Select external management > Deactivate.
- Select internal management > Deactivate.
- Activate both Ethernet connections as follows:
- Select external management > Activate.
- Select internal management > Activate.
- Select Back to return to the Network Manager TUI menu.
- On the Network Manager TUI menu, select Set system hostname, as shown.
- Change the Hostname from its default setting to the new hostname, omni.dell.labin this example. Dell recommends entering the OMNI hostname in FQDN format as shown.
- Click OK > OK > Quit.
- After services are started, the NTP Server IP/Hostname: prompt displays. At the prompt, specify the NTP server, ntp.dell.labin this example, as shown in the figure below.Note: If an NTP server is not used, press Enter to skip.
- At the Install SSL Certificates from remote server [y]? prompt, enter n.Note: OMNI certificate installation is outside the scope of this guide. Certificates can be imported later by selecting 5. Password/SSL configuration menu from the OMNI Menu. Follow the instructions provided in the OpenManage Network Integration for SmartFabric Services User Guide, Release 3.2. The guide is available on the Dell EMC OpenManage Network Integration website.
- Press Enter to return to the OMNI menu.
- On the OMNI menu, select 8. Logout.
This completes the OMNI VM console configuration.